M Press Copper Full Crossover
The M Press Copper Full Crossover provides a neat solution for routing compatible copper pipework around another pipe or obstruction. Its formed crossover section creates an offset within the fitting, allowing one pipe run to pass around another without complicated on-site bending.
Both ends feature compatible M profile press connections. Therefore, installers can incorporate the crossover directly into copper pipework using suitable M profile pressing equipment.
The preformed design also helps create a consistent and professional finish. Furthermore, it can save installation time where pipe routes need to cross within restricted spaces.
Because the connections use press technology, there is no need for solder, flux or a blowtorch at the joints. Consequently, the fitting provides a practical option for domestic and commercial water and compatible heating installations.
Why Choose an M Press Copper Full Crossover?
Creates a Neat Pipe Crossover
The formed body allows compatible copper pipework to route around another pipe or suitable obstruction.
No On-Site Pipe Bending
The crossover shape is already formed. Therefore, installers can create an offset without manually bending a straight section of copper tube.
Press Connections at Both Ends
Both ends use compatible M profile press connections. Consequently, the crossover integrates neatly with M Press copper pipework.
Consistent Crossover Shape
A manufactured fitting provides a predetermined crossover. As a result, installers can achieve a clean and consistent appearance.
No Soldering Required
Mechanical press connections remove the need for solder and flux.
No Naked Flame
The fitting does not require a blowtorch at either press connection. Therefore, it helps reduce traditional hot works.
Key Features
- M Press copper full crossover
- Preformed crossover design
- Allows copper pipework to pass around another pipe
- Creates a controlled offset
- Press connection at both ends
- M profile press fitting
- Suitable for compatible copper tube
- No on-site crossover bending required
- Ideal for neat pipe routing
- Useful in restricted spaces
- Suitable for water applications
- Suitable for compatible heating systems
- No soldering required
- No flux required
- No blowtorch required
- Reduced hot works
- Fast mechanical jointing
- Professional appearance
- Suitable for new installations
- Ideal for refurbishment work
- Useful for pipework alterations
- Suitable for domestic plumbing
- Suitable for commercial plumbing
- Compatible press tool required
- Correct M profile jaw required
Technical Specification
- Product: M Press Copper Full Crossover
- Product Type: Full Crossover / Pipe Crossover
- Connection Type: Press x Press
- Press Profile: M Profile
- Pipe Material: Compatible Copper Tube
- Application: Water, Plumbing and Compatible Heating Systems
- Function: Routing Pipework Around Another Pipe or Suitable Obstruction
- Jointing Method: Mechanical Press Connection
- Number of Press Connections: Two
- Soldering Required: No
- Flux Required: No
- Open Flame Required: No
- Press Tool Required: Yes
- Press Jaw Required: Correct Size M Profile Jaw
Always confirm fitting dimensions, copper tube specification and system compatibility before installation.
What Is an M Press Full Crossover?
An M Press Full Crossover is a preformed copper fitting designed to create an offset within a pipe run.
Rather than following a straight line, the fitting moves away from its original route and then returns to it.
Therefore, another pipe can pass through the space created by the crossover.
This makes the fitting particularly useful when two copper pipe runs need to cross without interfering with each other.
The full crossover then reconnects to compatible copper tube at both ends.
What Is a Copper Crossover Used For?
Copper pipework often needs to navigate around other building services.
For example, two pipes running along the same wall may need to cross.
Without a crossover, the installer could need to form an offset manually using bends or additional fittings.
A full crossover provides a purpose-designed alternative.
Therefore, it can help route copper pipework around:
- Other copper pipes
- Heating pipework
- Water pipework
- Existing services
- Suitable small obstructions
- Closely positioned pipe runs
Full Crossover vs Bending Copper Pipe
Installers can create offsets by bending suitable copper tube.
However, this requires the correct bending equipment, sufficient working space and careful measurement.
An M Press Full Crossover provides a preformed alternative.
Therefore, potential advantages include:
- No manual crossover bending
- Consistent shape
- Quick installation
- Neat appearance
- Predictable pipe routing
- Useful where bending space is restricted
The correct approach will depend on the individual installation and available space.
Full Crossover vs Multiple Elbows
Another way to create an offset involves several elbows and short pieces of copper tube.
However, this can increase the number of components and connections.
A full crossover incorporates the offset into a single fitting.
Therefore, it can provide:
- Fewer individual fittings
- Fewer press connections
- Less assembly work
- Compact pipe routing
- Cleaner appearance
- Faster installation
Furthermore, fewer individual components can simplify the finished pipe layout.
Ideal for Crossing Copper Pipe Runs
Parallel copper pipes can sometimes need to change position.
For example, one pipe may need to move from one side of another pipe to the opposite side.
The full crossover creates the required offset and then returns the pipe to its original line.
Consequently, installers can create an organised crossover without introducing a complicated arrangement of elbows and short pipe sections.
Ideal for Neat Surface Pipework
Visible copper pipework benefits from accurate and consistent routing.
Poorly formed bends or complicated fitting arrangements can affect the finished appearance.
A manufactured full crossover provides a controlled shape.
Therefore, it can help produce neat pipework where copper remains visible.
This can prove useful in:
- Utility rooms
- Plant rooms
- Boiler rooms
- Service areas
- Commercial installations
- Exposed plumbing layouts
Copper Press Fittings for Water
M Press technology provides a mechanical method of joining compatible copper tube.
The installer prepares the copper pipe, inserts it into the fitting and completes the connection with compatible pressing equipment.
Therefore, the process does not require soldering at the joint.
Typical applications include:
- Hot water pipework
- Cold water pipework
- Water distribution
- Domestic plumbing
- Heating installations
- Plant rooms
- Commercial plumbing
- New build projects
- Refurbishments
- Maintenance work
No Soldering Required
Traditional copper installations commonly use soldered joints.
However, M Press technology uses mechanical pressing instead.
Therefore, installers do not need:
- Solder
- Flux
- Blowtorch
- Naked flame at the connection
This allows professional installers to retain copper pipework while using a modern mechanical jointing method.
Reduced Hot Works
Copper pipework can pass close to timber, insulation, walls and finished surfaces.
Using a blowtorch in these areas may require additional precautions.
M Press connections avoid applying a naked flame to the joint.
Consequently, the M Press Full Crossover can prove particularly useful during refurbishment and maintenance work.
Ideal for Restricted Spaces
Creating a neat crossover manually requires enough space to form the necessary pipe bends.
However, many installations offer limited working room.
A preformed crossover can simplify the process.
Therefore, it can prove useful in:
- Service cupboards
- Utility rooms
- Boiler cupboards
- Plant rooms
- Existing plumbing systems
- Refurbishment projects
- Confined service areas
Always check the physical dimensions of the fitting against the available installation space.
Ideal for Heating Pipework
Heating systems can contain several copper pipes running alongside each other.
Occasionally, those pipes need to cross.
A full crossover provides a neat method of moving one compatible pipe around another.
Therefore, it can be useful within suitable:
- Boiler installations
- Heating distribution systems
- Radiator pipework
- Plant rooms
- Cylinder installations
- Pump arrangements
- Valve assemblies
Correct pipe sizing and system design should always determine the final layout.
Ideal for Plumbing Alterations
Existing pipework can make refurbishment work challenging.
New pipes may need to cross existing services without completely rerouting the installation.
Therefore, a full crossover can provide a useful solution.
Furthermore, M Press connections eliminate the need for soldering at the joints.
As a result, the fitting works particularly well for pipework modifications in existing properties.
How to Install an M Press Copper Full Crossover
Correct pipe preparation remains essential.
Firstly, plan the pipe route and confirm that the crossover provides sufficient clearance for the pipe or obstruction being crossed.
Next, cut the compatible copper tube squarely using a suitable pipe cutter.
Remove internal and external burrs from both cut ends.
Then, inspect the copper tube for damage or distortion.
Mark the required insertion depth on each pipe where specified.
Push both copper tubes fully into the crossover fitting.
Check the insertion marks.
Next, position the correct size M profile press jaw over the first designated pressing section.
Complete the full pressing cycle.
Repeat the process on the second connection.
Finally, inspect both completed joints before commissioning the system.
Check Crossover Clearance Before Installation
A full crossover has a predetermined shape.
Therefore, installers should check the available clearance before cutting and assembling the pipework.
Confirm that the crossover can pass around the intended pipe or obstruction without unwanted contact.
Furthermore, allow for any insulation or other installation requirements around the pipework.
Planning the crossover position before pressing helps prevent unnecessary alterations later.
Always Deburr Copper Pipe
Freshly cut copper tube can have sharp edges.
Therefore, both pipe ends should be properly deburred before entering the fitting.
Correct preparation helps protect the internal sealing components.
Furthermore, it allows the copper tube to enter smoothly and reach the required insertion depth.
A suitable pipe reamer or deburring tool should form part of every professional M Press installation kit.
Mark Both Insertion Depths
The full crossover has two press connections.
Therefore, installers should mark and check the insertion depth at both ends where required.
These marks provide a simple visual reference before pressing.
Furthermore, they help identify accidental pipe movement while positioning the press tool.
Both Connections Must Be Pressed
The M Press Full Crossover has a press socket at each end.
Therefore, both connections require a complete press cycle.
Firstly, check the pipe position.
Next, press the first connection.
Then, reposition the tool and press the second connection.
Finally, inspect both joints.
A systematic approach helps prevent an unpressed connection from being overlooked.
Use the Correct M Profile Jaw
The fitting requires compatible M profile pressing equipment.
Before pressing, check:
- Fitting size
- Copper tube size
- M press profile
- Correct jaw size
- Press tool compatibility
- Jaw condition
- Pipe insertion depth
- Correct jaw positioning
Never use another press profile simply because the jaw appears to fit around the fitting.
Manual or Powered M Press Tool?
The fitting should only be installed using compatible pressing equipment suitable for its exact size.
A manual M Press tool may provide a practical option where the tool and jaws support the crossover size.
Alternatively, a compatible powered press tool can make repetitive installation quicker.
Therefore, always confirm tool and jaw compatibility before pressing.
M Press Full Crossover for Plant Rooms
Plant rooms often contain multiple copper pipe runs positioned close together.
Consequently, pipe routes can become complex.
Full crossovers provide another option when installers need one pipe to pass around another while maintaining an organised layout.
They can prove particularly useful around:
- Boilers
- Cylinders
- Pumps
- Valves
- Manifolds
- Heat exchangers
- Heating controls
- Water distribution pipework
Furthermore, M Press technology helps reduce traditional hot works within the installation area.
M Press Full Crossovers for Commercial Installations
Commercial buildings can contain extensive copper distribution systems.
Therefore, installers may encounter numerous areas where pipe routes need to cross.
M Press Copper Full Crossovers can form part of compatible installations within:
- Hotels
- Apartment developments
- Offices
- Schools
- Retail properties
- Public buildings
- Plant rooms
- Residential developments
- Commercial refurbishments
- Maintenance projects
The preformed design can also help maintain a consistent appearance across larger projects.
Complete M Press Copper Fitting System
The M Press Copper Full Crossover forms part of a wider copper press fitting system.
Therefore, installers can combine compatible fittings to create:
- Straight connections
- 45° direction changes
- 90° direction changes
- Pipework crossovers
- Offsets
- Equal branches
- Reduced branches
- Pipe size reductions
- Pipe terminations
- Threaded transitions
Using a compatible M profile system throughout an installation provides a consistent mechanical jointing method.
Why Buy From Kudos Trading?
Kudos Trading supplies professional plumbing, heating and underfloor heating products throughout the UK.
With more than 25 years of relevant industry experience, we understand the importance of practical products, dependable service and knowledgeable support.
Furthermore, our growing M Press copper range allows professional installers to source fittings alongside compatible tools and pipe preparation equipment.
Choose Kudos Trading for:
- Extensive M Press copper fitting range
- Professional plumbing and heating products
- Competitive UK pricing
- Fast nationwide delivery
- Practical technical support
- Friendly customer service
- More than 25 years of industry experience
- Support before and after your purchase
Frequently Asked Questions
What is an M Press Copper Full Crossover?
It is a preformed copper press fitting that creates an offset so one pipe run can pass around another pipe or suitable obstruction.
What is a full crossover used for?
It is primarily used when copper pipework needs to cross another pipe while maintaining a neat installation.
Does the crossover connect to copper pipe at both ends?
Yes. The full crossover has compatible press connections at both ends.
What press profile does it use?
The fitting requires compatible M profile pressing equipment.
Does the fitting require soldering?
No. Mechanical pressing completes the connections.
Do I need a blowtorch?
No. M Press fittings provide a flame-free jointing method at the connection.
Is the fitting suitable for water pipework?
Yes. It is intended for compatible copper water and plumbing applications.
Can it be used on heating pipework?
Yes, where the fitting and complete system specification permit its use within the intended water-based heating application.
Can it pass around another copper pipe?
Yes. That is one of the main purposes of a crossover. However, always check the fitting dimensions and required clearance first.
Does a full crossover join the two crossing pipes?
No. The crossover routes one pipe around the other. It does not create a connection between the two pipe runs.
Is a full crossover the same as a cross fitting?
No. A cross fitting creates connected branches. A full crossover simply allows one pipe route to pass around another without joining them.
Can a crossover replace several elbows?
In suitable installations, yes. Its preformed offset can avoid creating a crossover from multiple elbows and short pipe sections.
Can it replace a manually bent copper crossover?
Yes, where its dimensions and clearance suit the installation.
Do both ends need pressing?
Yes. Both press connections must be correctly completed.
Do I need to deburr both pipes?
Yes. Properly cut and deburr both copper tube ends before inserting them into the fitting.
Should I mark the insertion depth?
Yes, where specified. Marking both pipe ends provides a useful visual check before pressing.
Can I use a U profile jaw?
No. Use the specified compatible M profile equipment.
Can I use a manual M Press tool?
Yes, but only where the manual tool and jaw are compatible with the exact fitting size.
Can I use a powered press tool?
Yes, provided the press tool and M profile jaw are compatible with the fitting.
Is a full crossover useful in plant rooms?
Yes. It provides a neat way to route compatible copper pipework around other services in complex plant room installations.
Related Products
- M Press Copper Equal Tees
- M Press Copper Reducing Tees
- M Press Copper Reducing Couplers
- M Press Copper Fitting Reducers
- M Press Copper Straight Couplers
- M Press Copper Sleeve Couplings
- M Press Copper End Stops
- M Press Copper 90° Elbows
- M Press Copper 90° Street Elbows
- M Press Copper 45° Elbows
- M Press Copper 45° Street Elbows
- Manual M Press Tool
- M Profile Press Jaws
- Copper Pipe Cutters
- Pipe Reamers & Deburring Tools
Next Working Day Delivery: Yes, we hold all our products in stock at our 7000 sq ft Nottingham warehouse and at our 3000 sq ft warehouse in Market Harborough and use DPD for a tracked next-day delivery.
Collection Available: You can always collect from our Norttinagham location and help yourself to a free tea and coffee
